Upgraded ATS-25X1 All Band DSP Radio Receiver FM LW MW With Touch Screen 2.4 U3. Usdx/r+ Plus V2 8 Band SDR Full Mode HF Ham Radio SSB QRP Transceiver Upgrade U3. 5W 8-Band USDX USDR HF QRP SDR Transceiver SSB/CW DSP w/ Mic Charger. It has 1602 screen, built-in battery, equipped with charger, built-in microphone, built-in speaker! It can be connected to an auto key and can be cw decoded.
Characteristics: -Using Osmo series launch tube, durable -Can be used by connecting the antenna (M seat) -8 bands. 13.8v 10w maximum external power!Built-in 12.6v battery -Dimensions: 76x46x130mm/3x1.8x5.1 -Provides FT8 option connector later -Use tcxo for kds. Accuracy 0.5ppm (1ppm per year) - Aluminum shell laser marking -Fully aluminum buttons! 99mhz performance loss -Open source, integrated firmware for Arduino IDE; allows experimentation, can add new functions, can share contributions via github, software complexity: 2000 lines of code -Software based VOX can be used as a quick and full raid (QSK and Semi-QSK operation), or to assist in running in digital mode (no cat or ptt interface) for rx/tx switching, external delayed ptt output control tx/pa -Simple installation modification with 8 component changes and 8 wires -Lightweight and cost-effective transceiver: thanks to the level and eer transmitter, it has high energy efficiency (no bulky heat sink needed) and simple Design (no complex balanced linear power amplifiers required) -SSB transmitter stage entirely based on digital and software: by controlling the phase of the PLL SI5351 (through the small frequency shift of I2C above 800kbit/s) and the amplitude of the PA (through the PWM of PWM) to sample the microphone input and reconstruct the ssb signal.
Pa key shaping circuit -Software-based, all-digital SDR receiver stage (optional): samples the I/Q (complex) signal from the digital mixer from the square sampling detector, and perform a 90 degree phase shift in the software (hilber transform) and eliminate one by adding sidebands -Three independently switchable analog front receiver faders (0db, -13db, -20db, -33db, -53db, -60db, -73db) - MDS receiver noise level: -135 dbm (200hz bw) to 28mhz - Receiver front selectivity: Steep tuning frequency -45db/ten times roll-off/-2khz - Lock dynamic range: 20khz offset 123db, 2khz offset 78db - CW decoder, straight/iambic-a/b keyboard -Vfo a/b scrit and split, and switch the corresponding relay band filter via i2c -Support for cat (TS480 subset), you can stream audio, press keys and display text through cat -This is probably the most economical and easiest to build standalone SDR/SSB transceiver. Great simplification simplifies the original QCX circuit i. Reduces installation components by 50%, reduces installation components by 50%, does not require complex transformer windings and does not require alignment procedures, and is more versatile Port introduction: -Charge: Built-in lithium battery charging port and you can only use the charger provided! It is forbidden to use other chargers! -Switch: off to turn off.
Bat: Built-in battery power supply. 13.8: external power supply -DC13.8v/3a: external power supply port -Key: Automatic key body connection (A, B, single key) -Pa: external power amplifier, PTT signal -Microphone: External microphone port -Uart: serial communication port (osmo compatible) -Spk: external speaker Package included: 1 x Transceiver 1 x Power Adapter 1 x Mic 1 x 3 in 1 screwdriver. If you are not satisfied with the item after you receive it. Please don't return with the address on the package.
We will try our best to give you the best solution. If you have any questions, please feel free advice on us by Message. We always reply you within 24 hours except weekends.
We will try our best to service you. VIPIH fulfills all needs of its clients completely and on a timely basis with the know-how it has built up since it was established and the comprehension knowledge of the sectors standards. VIPIH is presently capable of supplying all demands from the car windshield wiper systems to Ignition switch in a wide range.
If you need any further information before ordering or cannot locate what you need then please get in touch our dedicated team are on hand with expert advice and assistance.