50K 2GHz Register Malachite SDR Radio Malahit DSP SDR Receiver LCD Display. ATS-25X1 Si4732 Full-Band Radio Receiver DSP FM LW MW SSB + 2.4 Touch Screen. USDX USDR SDR Transceiver QRP SSB/CW Transceiver All Mode 8 Band HF Ham Radio.USDX USDR SDR Transceiver All Mode 8 Band HF Ham QRP CW Transceiver Radio. USDX USDR HF QRP SDR Transceiver 8-Band 5W SSB DSP CW Transceiver For Ham Radio. USDX USDR HF QRP SDR Transceiver 8-Band 5W DSP SSB/CW Transceiver For Ham Radio. All Mode 8 Band USDX USDR SDR Transceiver HF Ham Radio QRP CW Transceiver. 8-Band USDX USDR HF QRP SDR Transceiver SSB/CW 5W DSP SDR For Ham Radio.
This is a shortwave QRP SSB/CW transceiver. It boasts 1602 screen, built-in battery, equipped with charger, built-in mic, built-in speaker! It can be connected to an automatic key, and can be decoded by cw. Using IRF series launch tube, durable. Can be used by connecting the antenna (M seat).
Power standing wave digital display! External 13.8v maximum power 10w! Dimensions: 76 x 46 x130mm/3 x 1.8 x 5.1. Provide ft8 option connector later. Accuracy 0.5PPM (1PPM per year).
Translucent silica gel button (receive green, emit red). Simple, interesting and versatile QRP SSB HF transceiver with embedded DSP and SDR functions. EER E-level driven SSB launch stage. 13.8V power supply provides about 10W PEP SSB output.DSP filter: 4000, 2500, 1700, 500, 200, 100, 50Hz passband. DSP function: automatic gain control (AGC), noise reduction (NR), voice trigger, voice trigger Xmit (VOX), RX attenuator attenuator (ATT), TX noise gate, TX driver control, volume control, dBm/S-meter. SSB reverse sideband/carrier suppression transmission: better than -45dBc, IMD3 (two tones) -33dBc, reception: better than -50dBc. Multi-band support, continuously adjustable in the 160m-10m frequency band and performance loss from 20kHz.. Open source firmware, built in for Arduino IDE; allows experimentation, can add new functions, can share contributions through Github, software complexity: 2000 lines of code. Software-based VOX can be used as a fast full invasive (QSK and semi-QSK operation), or to assist in running in digital mode (without CAT or PTT interface) for RX/TX switching, external PTT output with TX/PA control-delay. Simple installation modification with 8 component changes and 8 wires.
Lightweight, low-cost transceiver: Thanks to EER transmitter E-level, it has high power efficiency (no bulky heat sink required), and simple design (no need for complex balanced linear power amplifiers). SSB transmitter stage based entirely on digital and software: By controlling the phase of the SI5351 PLL (via the tiny frequency change of I2C over 800kbit/s) and the amplitude of the PA (via the PWM of PWM) to sample the microphone input and reconstruct the SSB signal. Fully digital and software-based SDR receiver stage (optional): sample the I/Q (complex) signal from the quadrature sampling detector digital mixer, and perform a 90-degree phase shift in the software (Hilber transform) and eliminate one by adding sidebands.
Three independent switchable analog front-end receiver attenuators (0dB, -13dB, -20dB, -33dB, -53dB, -60dB, -73dB). Receiver noise level MDS: -135 dBm (200Hz BW) at 28MHz. Receiver front-end selectivity: steep tuning frequency -45dB / ten times roll-off +/- 2kHz.
Blocking dynamic range: 20kHz offset 123dB, 2kHz offset 78dB. VFO A/B + RIT and and Split, and switch the corresponding relay band filter through I2C. CAT support (TS480 subset), you can stream audio, press keys, and display text through CAT.This is probably the most cost-effective and easy to build standalone SDR/SSB transceiver. Great simplification Simplifies the original QCX circuit (that is, reduces the installation components by 50%, reduces the installation components by 50%, does not require complex transformer windings, and does not require alignment procedures), and is more versatile. Charge: Charging port of the built-in lithium battery and you can only use the supplied charger! It is forbidden to use other chargers! Switch: OFF to shut down. BAT: Built-in battery power supply. 13.8: External power supply. DC13.8V/3A: External power supply port. KEY: automatic key body connection (A, B, single key). PA: External power amplifier, PTT signal. UART: Serial communication port (command compatible with TS-480). 1 x Set of Transceiver. Amazing designs, unsurpassed quality and unbeatable savings! We know what you demand: supremely stylish, ergonomically-crafted products of long-lasting, durable quality. All at a price that's highly affordable! You also want those glasses to fit comfortably-guaranteed! We want your online shopping experience to be risk free. Please make sure that the item is in the same condition that you received it. This item is in the category "Consumer Electronics\Radio Communication\Ham, Amateur Radio\Ham Radio Transceivers". The seller is "hmtrading01" and is located in this country: CN. This item can be shipped worldwide.