Reliable Work: A pocket sized 8 band SSB CW QRP transceiver designed with built in lithium battery, built in microphone, PTT button and extremely low RX current consumption, it is a good partner for SOTA, POTA or any other portable activities. Better Design: This QRP SSB CW shortwave transceiver has a large screen, built in battery, charger, built in microphone and speaker. It can be connected to an automatic button.It can also be decode CW coding. IRF Tube: With durable IRF series tube, can be used to connect antenna, which is on the instrument base. Simple Structure: All aluminum buttons and translucent silicone buttons, the original transformer qcx circuit is greatly simplified, and the installation components are reduced by 50%. There is no wiring procedure.
High Efficiency: High power efficiency and simple design, thanks to eer electronic level transmitters, also very convenient to carry. Function: Radio Transceiver: A QRP SSB HF transceiver with embedded DSP and SDR functions. EER E level driven SSB stage. Output: 13.8V power supply provides about 10W PEP SSB output.
DSP Function: Automatic gain control (AGC), noise reduction (NR), voice trigger, voice trigger Xmit , RX attenuator attenuator (ATT), TX noise gate, TX driver control, volume control, dBm S meter SSB Reverse Sideband and Carrier Suppression Transmission: Better than -45dBc Two Tones IMD3: -33dBc, reception: better than -50dBc. Multi Band Support: Continuously adjustable in the 160m-10m frequency band, and performance loss from 20kHz to 99MHz. Open Source Firmware, Built in for IDE: Allows experimentation, can add new functions, can share contributions through Github, software complexity: 2000 lines of code. Features: Software based can be used as a fast full invasive (QSK and semi QSK operation), or to assist in running in digital mode (without CAT or PTT interface) for RX/TX switching, external PTT output with TX/PA control delay Installation: Simple installation modification with 8 component changes and 8 wires. High Efficiency: Thanks to EER transmitter E level, it has high power efficiency (no bulky heat sink required), and simple design (no need for complex balanced linear power amplifiers).
SSB Transmitter Stage Based Entirely on Digital and Software: By controlling the phase of the SI5351 (via the tiny frequency change of I2C over 800kbit/s) and the amplitude of the PA (via the PWM of PWM) to sample the microphone input and reconstruct the SSB signal. Fully Digital and Software Based SDR Receiver Stage (optional): Sample the I/Q (complex) signal from the quadrature sampling detector digital mixer, and perform a 90 degree phase shift in the software (Hilber transform) and eliminate one by adding sidebands. 3 Independent Switchable Analog Front End Receiver Attenuators: 0dB, -13dB, -20dB, -33dB, -53dB, -60dB, -73dB Receiver Noise Level MDS: -135 dBm (200Hz BW) at 28MHz. Receiver Front End Selectivity: Steep tuning frequency -45dB, ten times roll off +/- 2kHz Blocking Dynamic Range: 20kHz offset 123dB, 2kHz offset 78dB. CW Decoder: Straight, Iambic-A, B keyer, VFO A/B + RIT and Split, and switch the corresponding relay band filter through I2C Supporting CAT with TS480 Subset: You can stream audio, press keys, and display text through CAT.SDR SSB transceiver: Great simplification simplifies the original QCX circuit, that is, reducing the installation components by 50%, does not require complex transformer windings, and does not require alignment procedures. Port Introduction: Charge: Charging port of the built in lithium battery and can only use the supplied charger. It is forbidden to use other chargers Switch: OFF to shut down.
BAT: Built in battery power supply. 13.8: External power supply DC 13.8V 3A: External power supply port KEY: Automatic key body connection, A, B, single key.
PA: External power amplifier, PTT signal. UART: Serial communication port, command compatible with TS-480. 1 x 3 in 1 Screwdriver. Our listing price includes the value of goods, packaging cost, and export.
Please check with your country's. We will reply your message within 48 hours. If you do not receive our reply within 48 hours, pls. Post a message again because sometimes our message system may block some emails.If you are satisfied with our service, pls. Our aim is to provide Level Customer Service, your recognition will encourage us greatly and serve you better. We strive to keep all our customers satisfy. We will do our up most to exceed your expectations in customer service, communication and dispatching of your orders.