3KG 3D Printer Filament 1.75mm ABS PLA PETG For Creality Ender 3/5 Pro CR-10S. Adult Sex Swing 360 Spinning Swivel Swing Position Enhancer For Couples Set EP. Tree Climbing Spike Set 2 Gears Safety Belt Adjustable Lanyard Rope Rescue EP.Remote Control Snake Rattlesnake Animal Trick Terrifying Mischief Random EP. Propane Torch Weed Burner Ice Snow Melter / Flame Dragon Wand Igniter Roofing EP. Water Hookah smoking pipe glass pipes glassware bong glass Aliens pipes EP. 700g High Speed Electric Herb Grain Grinder Cereal Mill Flour Powder Machine EP.
Airsoft Holographic Red US Scope Dot 551 Tactical Sight Sight Green US STOCK EP. 52CC 20 Gasoline Chainsaw Powered Wood Cutting Engine Gas Crankcase Chain Saw 9. Dampener Limb Vibration Bow Stabilizer Compound Split Super 2X Quad Limbsaver EP. 1PCS Car Charger Battery Eliminator Fit For XTS3000/5000/3500 MTP200 2-Way EP.
C-MORE Red Dot Reflex Sight Railway Tactical Scope Adjustable Optics Scope EP. 3/8" 1/2" 5/8" 3/4" 1 5in1 Pex Crimper Kit Copper Ring Crimping Plumbing Tool P.
5 Gallon Generator Gas Tank Fuel Filter Cap Gauge Petcock Universal Fit EC2500 E. Swimming Floating Chair Pool Seats Inflatable Lazy Water Bed Lounge Chairs EP. USDX USDR HF QRP Transceiver SSB/CW Transceiver 8-Band 5W DSP con Microfono EP. It has 1602 screen, built-in battery, equipped with charger, built-in microphone, built-in speaker! It can be connected to an auto key and can be cw decoded.Characteristics: -Using Osmo series launch tube, durable -Can be used by connecting the antenna (M seat) -8 bands. 13.8v 10w maximum external power! Built-in 12.6v battery -Dimensions: 76x46x130mm/3x1.8x5.1 -Provides FT8 option connector later -Use tcxo for kds.
Accuracy 0.5ppm (1ppm per year) - Aluminum shell laser marking -Fully aluminum buttons! 99mhz performance loss -Open source, integrated firmware for Arduino IDE; allows experimentation, can add new functions, can share contributions via github, software complexity: 2000 lines of code -Software based VOX can be used as a quick and full raid (QSK and Semi-QSK operation), or to assist in running in digital mode (no cat or ptt interface) for rx/tx switching, external delayed ptt output control tx/pa -Simple installation modification with 8 component changes and 8 wires -Lightweight and cost-effective transceiver: thanks to the level and eer transmitter, it has high energy efficiency (no bulky heat sink needed) and simple Design (no complex balanced linear power amplifiers required) -SSB transmitter stage entirely based on digital and software: by controlling the phase of the PLL SI5351 (through the small frequency shift of I2C above 800kbit/s) and the amplitude of the PA (through the PWM of PWM) to sample the microphone input and reconstruct the ssb signal. Pa key shaping circuit -Software-based, all-digital SDR receiver stage (optional): samples the I/Q (complex) signal from the digital mixer from the square sampling detector, and perform a 90 degree phase shift in the software (hilber transform) and eliminate one by adding sidebands -Three independently switchable analog front receiver faders (0db, -13db, -20db, -33db, -53db, -60db, -73db) - MDS receiver noise level: -135 dbm (200hz bw) to 28mhz - Receiver front selectivity: Steep tuning frequency -45db/ten times roll-off/-2khz - Lock dynamic range: 20khz offset 123db, 2khz offset 78db - CW decoder, straight/iambic-a/b keyboard -Vfo a/b scrit and split, and switch the corresponding relay band filter via i2c -Support for cat (TS480 subset), you can stream audio, press keys and display text through cat -This is probably the most economical and easiest to build standalone SDR/SSB transceiver. Great simplification simplifies the original QCX circuit i.
Reduces installation components by 50%, reduces installation components by 50%, does not require complex transformer windings and does not require alignment procedures, and is more versatile Port introduction: -Charge: Built-in lithium battery charging port and you can only use the charger provided! It is forbidden to use other chargers! -Switch: off to turn off. Bat: Built-in battery power supply.
13.8: external power supply -DC13.8v/3a: external power supply port -Key: Automatic key body connection (A, B, single key) -Pa: external power amplifier, PTT signal -Microphone: External microphone port -Uart: serial communication port (osmo compatible) -Spk: external speaker Package included: 1 x Transceiver 1 x Power Adapter 1 x Mic 1 x 3 in 1 screwdriver. My goal is to make sure you are a happy customer and pleasant shopping with us. International Buyers - Please Note. Thank you for your understanding.We stand behind everything that we sell and will do everything possible to assure you are satisfied. Buyers are responsible for the postal cost of returning the items. We must be notified of the intent to return your item within 30 days of receiving the item. How to return 1, Please ask us for return address. We strive to answer all questions and resolve any problems as quickly as possible.
This item is in the category "Consumer Electronics\Radio Communication\Ham, Amateur Radio\Ham Radio Transceivers". The seller is "eforshop-14" and is located in this country: CN. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.