5W 8-Band USDX USDR HF QRP Transceiver SSB/CW Transceiver DSP w/ Mic Charger E4. Usdr usdx+Plus V2 8 Band SDR Full Mode HF Transceiver w/Power Adapter US Plug EP. Upgraded ATS-25X1 All Band DSP Radio Receiver FM LW MW SW & 2.4 Touch Screen EP.
USDX USDR HF QRP SDR Transceiver SSB/CW Transceiver 8-Band 5W DSP SDR With Mic E. Usdr usdx + Plus V2 Transceiver 3W-5W All Mode 8 Band HF Ham Radio EP. Usdr usdx+ Plus V2 Transceiver 3W-5W All Mode 8 Band HF Ham Radio Transceiver EP.
New ATS-25X1 Si4732 All Band DSP Radio Receiver FM LW MW SW 2.4 Touch Screen EP. Upgraded ATS-25X1 All Band DSP Radio Receiver FM LW MW With 2.4 Touch Screen EP. USDX USDR HF QRP Transceiver SSB/CW Transceiver 8-Band 5W DSP con Microfono EP. It has 1602 screen, built-in battery, equipped with charger, built-in microphone, built-in speaker! It can be connected to an auto key and can be cw decoded.
Characteristics: -Using Osmo series launch tube, durable -Can be used by connecting the antenna (M seat) -8 bands. 13.8v 10w maximum external power! Built-in 12.6v battery -Dimensions: 76x46x130mm/3x1.8x5.1 -Provides FT8 option connector later -Use tcxo for kds.Accuracy 0.5ppm (1ppm per year) - Aluminum shell laser marking -Fully aluminum buttons! 99mhz performance loss -Open source, integrated firmware for Arduino IDE; allows experimentation, can add new functions, can share contributions via github, software complexity: 2000 lines of code -Software based VOX can be used as a quick and full raid (QSK and Semi-QSK operation), or to assist in running in digital mode (no cat or ptt interface) for rx/tx switching, external delayed ptt output control tx/pa -Simple installation modification with 8 component changes and 8 wires -Lightweight and cost-effective transceiver: thanks to the level and eer transmitter, it has high energy efficiency (no bulky heat sink needed) and simple Design (no complex balanced linear power amplifiers required) -SSB transmitter stage entirely based on digital and software: by controlling the phase of the PLL SI5351 (through the small frequency shift of I2C above 800kbit/s) and the amplitude of the PA (through the PWM of PWM) to sample the microphone input and reconstruct the ssb signal. Pa key shaping circuit -Software-based, all-digital SDR receiver stage (optional): samples the I/Q (complex) signal from the digital mixer from the square sampling detector, and perform a 90 degree phase shift in the software (hilber transform) and eliminate one by adding sidebands -Three independently switchable analog front receiver faders (0db, -13db, -20db, -33db, -53db, -60db, -73db) - MDS receiver noise level: -135 dbm (200hz bw) to 28mhz - Receiver front selectivity: Steep tuning frequency -45db/ten times roll-off/-2khz - Lock dynamic range: 20khz offset 123db, 2khz offset 78db - CW decoder, straight/iambic-a/b keyboard -Vfo a/b scrit and split, and switch the corresponding relay band filter via i2c -Support for cat (TS480 subset), you can stream audio, press keys and display text through cat -This is probably the most economical and easiest to build standalone SDR/SSB transceiver. Great simplification simplifies the original QCX circuit i. Reduces installation components by 50%, reduces installation components by 50%, does not require complex transformer windings and does not require alignment procedures, and is more versatile Port introduction: -Charge: Built-in lithium battery charging port and you can only use the charger provided!
It is forbidden to use other chargers! -Switch: off to turn off.
Bat: Built-in battery power supply. 13.8: external power supply -DC13.8v/3a: external power supply port -Key: Automatic key body connection (A, B, single key) -Pa: external power amplifier, PTT signal -Microphone: External microphone port -Uart: serial communication port (osmo compatible) -Spk: external speaker Package included: 1 x Transceiver 1 x Power Adapter 1 x Mic 1 x 3 in 1 screwdriver. My goal is to make sure you are a happy customer and pleasant shopping with us. International Buyers - Please Note. Thank you for your understanding.We stand behind everything that we sell and will do everything possible to assure you are satisfied. Buyers are responsible for the postal cost of returning the items. We must be notified of the intent to return your item within 30 days of receiving the item. How to return 1, Please ask us for return address. We strive to answer all questions and resolve any problems as quickly as possible.