3/10 Pack 3D Printer Filament 1.75mm ABS/PLA/PETG Thermoplastic Multicolor UE SF. 2 IN 1 Chainsaw Teeth Quick Sharpener File For STIHL. 325 4.8mm Chain F11. Red Green Dot Holographic Sight 551 Tactical Airsoft Scope Sight US F11.12 Hand Impulse Heat Sealer Plastic Bag Film Sealing Machine Metal ABS XW. Noise Cancelling Pilot Headset Fit for TK3107 TK3200 TK2160 BaoFeng BF-888S T1. 24 Double Sided Blade 26cc Gas Hedge Trimmer Recoil Gasoline Trim Blade F11. PLA 3D Printer Filament 1.75mm 1kg/2.2lb Spool 28 Multiple Colors 3D-filament XW. Mini 9D Stereo Headphones Earbuds Bluetooth 5.0 Headset Wireless TWS Earphone XW. External Laptop Graphics PCI E EXP GDC Video Card Dock NGFF Notebook V8.5 SF.
69800mAh Car Jump Starter Portable 4-USB Power Bank Battery Booster Clamp Kit US. Dryer Liquid Propane LP Propane Gas Conversion Kit Dryer Accessories 49572A H. MTB Mountain Bike 26 Wheels 21 Speed Bicycle Disc Bicycles SET F11.
62cc Gas Chainsaw 20 Bar Gasoline Powered Chain Saw 2 Cycle Engine Cutting F11. C-MORE Red Dot Reflex Sight Railway Tactical Scope Adjustable Optics Scope T1. 2 Pex Crimper 1/2" And 3/4" Plumbing Crimping Gonogo Set Angle Gauge Tools XQ.
USDX USDR HF QRP Transceiver SSB/CW Transceiver 8-Band 5W DSP con Microfono SF. It has 1602 screen, built-in battery, equipped with charger, built-in microphone, built-in speaker! It can be connected to an auto key and can be cw decoded. Characteristics: -Using Osmo series launch tube, durable -Can be used by connecting the antenna (M seat) -8 bands.
13.8v 10w maximum external power! Built-in 12.6v battery -Dimensions: 76x46x130mm/3x1.8x5.1 -Provides FT8 option connector later -Use tcxo for kds. Accuracy 0.5ppm (1ppm per year) - Aluminum shell laser marking -Fully aluminum buttons! 99mhz performance loss -Open source, integrated firmware for Arduino IDE; allows experimentation, can add new functions, can share contributions via github, software complexity: 2000 lines of code -Software based VOX can be used as a quick and full raid (QSK and Semi-QSK operation), or to assist in running in digital mode (no cat or ptt interface) for rx/tx switching, external delayed ptt output control tx/pa -Simple installation modification with 8 component changes and 8 wires -Lightweight and cost-effective transceiver: thanks to the level and eer transmitter, it has high energy efficiency (no bulky heat sink needed) and simple Design (no complex balanced linear power amplifiers required) -SSB transmitter stage entirely based on digital and software: by controlling the phase of the PLL SI5351 (through the small frequency shift of I2C above 800kbit/s) and the amplitude of the PA (through the PWM of PWM) to sample the microphone input and reconstruct the ssb signal. Pa key shaping circuit -Software-based, all-digital SDR receiver stage (optional): samples the I/Q (complex) signal from the digital mixer from the square sampling detector, and perform a 90 degree phase shift in the software (hilber transform) and eliminate one by adding sidebands -Three independently switchable analog front receiver faders (0db, -13db, -20db, -33db, -53db, -60db, -73db) - MDS receiver noise level: -135 dbm (200hz bw) to 28mhz - Receiver front selectivity: Steep tuning frequency -45db/ten times roll-off/-2khz - Lock dynamic range: 20khz offset 123db, 2khz offset 78db - CW decoder, straight/iambic-a/b keyboard -Vfo a/b scrit and split, and switch the corresponding relay band filter via i2c -Support for cat (TS480 subset), you can stream audio, press keys and display text through cat -This is probably the most economical and easiest to build standalone SDR/SSB transceiver.
Great simplification simplifies the original QCX circuit i. Reduces installation components by 50%, reduces installation components by 50%, does not require complex transformer windings and does not require alignment procedures, and is more versatile Port introduction: -Charge: Built-in lithium battery charging port and you can only use the charger provided! It is forbidden to use other chargers! -Switch: off to turn off.
Bat: Built-in battery power supply. 13.8: external power supply -DC13.8v/3a: external power supply port -Key: Automatic key body connection (A, B, single key) -Pa: external power amplifier, PTT signal -Microphone: External microphone port -Uart: serial communication port (osmo compatible) -Spk: external speaker Package included: 1 x Transceiver 1 x Power Adapter 1 x Mic 1 x 3 in 1 screwdriver. My goal is to make sure you are a happy customer and pleasant shopping with us. International Buyers - Please Note. Thank you for your understanding.We stand behind everything that we sell and will do everything possible to assure you are satisfied. Buyers are responsible for the postal cost of returning the items. We must be notified of the intent to return your item within 30 days of receiving the item.
How to return 1, Please ask us for return address. We strive to answer all questions and resolve any problems as quickly as possible. This item is in the category "Consumer Electronics\Radio Communication\Ham, Amateur Radio\Ham Radio Transceivers". The seller is "flyxiang-11" and is located in this country: CN.This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.